Corrugated wheeled hut thing

Here's something quite unusual, a corrugated iron hut near to a converted water mill that we've been staying in over Easter;

A closer view of the steering arrangement;

It looks smaller than a typical shepherds hut (not that I'm an expert), and the corrugated sides look more like a repair being laid over planking as this interior shots show;

And judging by the wheels it's not designed to move any real distance, just around a yard perhaps.

Here's a photo of the mill, called Barford Old Mill, near to Barford Saint Johns in Oxfordshire;

It's not as cool as Mapledurham (I wonder how many will get the reference!) but still very nice. The undershot wheel and workings are still in situ, although sensibly enclosed and no longer capable of being used;

The mill is also surrounded by red kites, I counted 10 in the air at one time.

Paul.

006 single plank waggon

I decided to try my hand at converting a 009 Society 1 plank wagon to 6mm gauge. I've built one before, seen here, and it is an excellent and affordable kit.

I started by chopping down the floor, cutting 4mm from the length (2 planks) and reducing the width to 16mm. Both ends could then be cut to suit, using a razor saw and cutting so the join was next to a stanchion;

With care and the tiniest amount of filler the join is invisible.

The sides had the same treatment;

I cut down along the corner plate on one side, glued the plate into place then once the glue had set reduced the length of the side to suit.

For the solebars I started by removing 1mm from each end, then removed a section from the middle so each solebar measured 24mm long. I added a strip of styrene behind each solebar for strengthening.

Here's one in place;

Note the .040" square styrene strip glued under the ends, this is to give larger surface to attach the couplings to.

As the solebars have been strengthened and shortened I decided to trap the wheelset in place now rather than spring it into place later, which I felt would be difficult as there's now less give in the axleboxes. So, I covered the treads in masking tape to protect them from paint;

Wheels are, as usual, home made. The diameter is 6mm, and they sit on 1.5mm dia. axles 12mm long with an approx. 54 degree taper turned on each end.

After giving the waggon a waft of grey Hycote primer I first painted the bare wood decking, using a Lifecolor Weathered Wood set (Warm Wood base, Warm Light Shade, followed by Warm Light Shade 2, then finished with Cold Light Shade). The rest of the body was brush painted with my go-to for non-mining 006 waggons, Vallejo 70.982 Cavalry Brown. Axleboxes are Vallejo 70.862 Black Grey. The number 12 (this is my 12th 006 waggon) was done with a mapping pen and white ink.

And forming part of a train on the as-yet-still-unfinished Drystone Moss;

On the left is my Borth van, detailed here, and on the right a R.A.R. gunpowder van, covered here.

To show how tiny this waggon is here's a couple of shots of it with a standard unmodified flat;

A successful conversion I'd say. The proportions suit the waggon well and I like the couplings and the extra material below the waggon ends.

Paul.

Bell pads

Something completely different.

I've mentioned before that I've taken up morris dancing, and for that you need kit. Bell pads are a part of that kit and are strapped to your calves and are, as the name suggests, covered in bells. 20 per leg in fact (the side supply the bells). Now, you can buy these, but I want to make my own kit (within reason, top hats are beyond most peoples skill sets). I found some instructions on-line courtesy of Berkeley Morris and those formed the basis of my plan.

As most bell pads are made of leather I started by buying a secondhand leather skirt from Vinted, a M&S one which cost me £4 plus postage;

It didn't fit me...

This I cut up into several panels;

I cut two of my panels down to 330 x 160mm, then marked out where I wanted the bells to sit as well as where the top and bottom folds over;

The punched holes (5mm) are for the ends of the slits, and are there to stop the slits from getting longer.

I then sewed the folds at the top and bottom, these are for the leg straps;

Leather is a sod to sew, at least in my hands. I used my 1960s Singer, which has just come back from being repaired (needle height problem), and I had to increase the foot pressure to get the material to feed properly. My sewing here is not the neatest, in fact it's pretty rubbish truth be told, but it will do. Thread is just normal Gutterman black.

To reinforce the area where the bells will sit I cut out strips of leather which I then glued behind the pads before re-marking out the bell positions and punching a series of 4mm holes using a home made punch;

For glue I used Evo-Stick, I find contact adhesive to be horrible stuff but it does the job. Please ignore the messy workmanship! Once the glue had set I cut three slits in each pad, so they could flex as I'm moving.

To hold the pads onto my legs I bought a pair of ready made straps complete with buckles from eBay, I did look at buying the webbing and buckles separately but ready made straps were a bit cheaper. These thread through the larger 'tunnel' at the top, the smaller 'tunnel' at the bottom has shoelaces threaded through. These are tied as loops, so I just need to step into them and pull the pads up to just under my knees and do the buckles up. The bottom of the pads sit fairly loose on the legs. More shoelaces are used to hold the bells in place, being threaded through the loops on the bells;

From the front;

And on me legs;

I decided that they were a little plain, so I punched three more holes in each to thread some ribbons through;

Much better.

I've enjoyed the challenge of making these, although I did find sewing the leather to be frustrating, maybe a walking foot would have helped. I have enough material to make another pair if these fail, or as a pair for someone else if I'm feeling generous.

Perhaps I'll wear them to exhibitions, after all they can't be any more irritating then those noisy diesel depots with the DCC sound turned up to 11. Or maybe I'll wear them on the bike, which would be especially useful on the Monsal Trail on a busy summers day.

Paul.