I've turned myself a new chimney for my Brian Madge small quarry Hunslet. There's nothing wrong with the casting supplied with the kit, but as I have a lathe and enjoy making things on it I decided that turning up a chimney would be an enjoyable way to spend a morning. Its also a way of adding a personal touch to the kit, and a turned chimney always looks better than even the finest casting.
The first job, as always, was to prepare a simple 'fag packet' sketch, dimensioned in millimetres, from the drawing in Cliff Thomas' excellent 'Quarry Hunslets of North Wales'.
This time I decided to take a different approach to forming the bottom flange, so I hand filed the end of a length of 5mm dia. bar to suit the smokebox, not too difficult as long as care is taken and the hand remains steady;
Of course this would be harder work if making the chimney for a larger loco, probably requiring fly-cutting.
The actual turning of the chimney was basically the same as for the Waril type, apart from leaving the bottom of the flange solid and the shape of the top cap, which is convex above the lip and concave below. The top of the lip was formed with a file, and the lower part formed using a round-nosed tool (as was the bottom flange). The bottom was also drilled with a 1mm drill so that it could be pinned to the smokebox. Here it is ready for the next operation;
Note the flat sections seen at the top and bottom of the smokebox flange, these needed blending in with a round needle file. So the turning was now removed from the chuck before parting off to make holding the chimney easier when filing.
The filing itself was just more steady work with a fine needle file and wet+dry. I wrapped a piece of masking tape around the parallel section to protect it from stray file marks, and checked the work regularly with a magnifying glass;
Once I was happy with the shape the chimney could be re-chucked in the lathe and parted off. The next job was to drill it out from the top. To do this I held it in a split mandrel (7mm dia. brass, skimmed over the top and drilled to suit the centre section of the chimney, then cut in half down the centre with a razor saw and parted off) and drilled it out to 1.8mm dia., 7mm deep;
And here's the end result, along with the supplied whitemetal casting and the split collet;
And placed on the loco;
Those that know a little of the history of my model will be interested to learn that the damage inflicted upon it (cab backsheet snapped off!) has now been repaired.
Paul.
Saturday, 28 June 2014
Wednesday, 25 June 2014
Roxey Mouldings ICI hopper part 6 - hopper 2.
The internal divider for the hopper body comprises of two parts, neither of which fit very well...
The lower section needs to be bent to shape, but first a fold line needs scoring along the centre in line with the two slots, easy work with a scrawker. Below can be seen one lower part still flat, one folded to shape and, on the right, an upper divider;
It is quite a poor fit, so its a case of fitting it with minimal gaps then soldering it in place. To try and remove more metal to achieve a tighter fit would only make the part too small, and its undersized as it is.
The upper part is also undersized, hence the gaps;
The next job is to attach the side ribs, 6 per side. However, these need modifying as the angle of the ribs as etched don't match the hopper sides (click on pic. for a larger image);
I filed the cusp of off the ribs then gently bent them to suit, a fiddly job, before soldering them in place;
The outermost ribs need trimming down at the bottom to suit the hopper ends.
They're getting there;
All soldering done with my trusty Antex XS25 and Eileen's Emporium 188 degree solder wire.
The next job is to attach the rivet strips to the hopper sides and ends, then solder the body to the chassis.
Paul.
The lower section needs to be bent to shape, but first a fold line needs scoring along the centre in line with the two slots, easy work with a scrawker. Below can be seen one lower part still flat, one folded to shape and, on the right, an upper divider;
It is quite a poor fit, so its a case of fitting it with minimal gaps then soldering it in place. To try and remove more metal to achieve a tighter fit would only make the part too small, and its undersized as it is.
The upper part is also undersized, hence the gaps;
The next job is to attach the side ribs, 6 per side. However, these need modifying as the angle of the ribs as etched don't match the hopper sides (click on pic. for a larger image);
I filed the cusp of off the ribs then gently bent them to suit, a fiddly job, before soldering them in place;
The outermost ribs need trimming down at the bottom to suit the hopper ends.
They're getting there;
All soldering done with my trusty Antex XS25 and Eileen's Emporium 188 degree solder wire.
The next job is to attach the rivet strips to the hopper sides and ends, then solder the body to the chassis.
Paul.
Friday, 6 June 2014
Turning a chimney for a OO9 Waril class Hunslet.
The Hunslet Warils were a class of 18" gauge well tank locos built for the Deptford Supply Reserve Depot during WW1. After the war 4 locos were sold to the Sand Hutton Railway. James Hilton is building a couple of these distinctive little locos using the new outside framed Minitrains chassis, and I'm planning on scratchbuilding a couple myself.
I started by finding a scale drawing and using it to produce a rough sketch of the chimney with all of the dimensions in millimetres.
A length of 5mm dia. brass was put in the chuck with 18mm sticking out. This was faced off and turned down to 4mm dia. (bottom flange dia.) 16.5mm long;
With a pointed turning tool fitted at an angle the part was turned to 3.4mm dia. (top cap outer dia.), starting 2.3mm from the end;
The centre section was then turned to 2.5mm dia. (finished dia. +.2mm);
Using a parting-off tool a 2.5mm dia. recess was cut above the top cap, to clear the forming tool;
The top cap shape was formed using a 1.6mm wide round nosed form tool, specially ground for the job;
Touch onto 2.5mm dia, move tool along until it touches corner of cap, move tool along .75mm.
At first I tried forming the cap using a round needle file, however I wasn't happy with the results ( I scrapped 4!), finding it difficult to make both radii consistant, especially as I wanted to make 5 identical chimneys..
The bottom radius however was formed with a needle file, larger diameters seem to be easier to form with a file;
With the pointed tool re-fitted the centre section was turned to its finished dia., 2.3mm, 10mm long. Remember that a chimney often consists of a tube sitting between cast top caps and flanges, which fit outside of the tube ends. Turning this section after forming the cast top and bottom sections means that it won't be marked if the file slips.
Centre drilling next, then the chimney was drilled through 1.5mm dia. To form the flange the inside of the bottom of the chimney is filed to a bell-mouth shape using a needle file, to reduce the wall thickness;
Then the chimney could be parted off to 14mm long.
To form the flange shape I set the machine up as a drill press, held the chimney upright using a little mandrel and squashed the base of the chimney against a length of half inch dia. stock (much the same as I did with the Px48 chimney);
Job done;
All turning and drilling done at 2000rpm, apart from forming and filing, 685rpm, and parting off, 365rpm.
Click on the photos for a larger image.
Paul.
I started by finding a scale drawing and using it to produce a rough sketch of the chimney with all of the dimensions in millimetres.
A length of 5mm dia. brass was put in the chuck with 18mm sticking out. This was faced off and turned down to 4mm dia. (bottom flange dia.) 16.5mm long;
With a pointed turning tool fitted at an angle the part was turned to 3.4mm dia. (top cap outer dia.), starting 2.3mm from the end;
The centre section was then turned to 2.5mm dia. (finished dia. +.2mm);
Using a parting-off tool a 2.5mm dia. recess was cut above the top cap, to clear the forming tool;
The top cap shape was formed using a 1.6mm wide round nosed form tool, specially ground for the job;
Touch onto 2.5mm dia, move tool along until it touches corner of cap, move tool along .75mm.
At first I tried forming the cap using a round needle file, however I wasn't happy with the results ( I scrapped 4!), finding it difficult to make both radii consistant, especially as I wanted to make 5 identical chimneys..
The bottom radius however was formed with a needle file, larger diameters seem to be easier to form with a file;
With the pointed tool re-fitted the centre section was turned to its finished dia., 2.3mm, 10mm long. Remember that a chimney often consists of a tube sitting between cast top caps and flanges, which fit outside of the tube ends. Turning this section after forming the cast top and bottom sections means that it won't be marked if the file slips.
Centre drilling next, then the chimney was drilled through 1.5mm dia. To form the flange the inside of the bottom of the chimney is filed to a bell-mouth shape using a needle file, to reduce the wall thickness;
Then the chimney could be parted off to 14mm long.
To form the flange shape I set the machine up as a drill press, held the chimney upright using a little mandrel and squashed the base of the chimney against a length of half inch dia. stock (much the same as I did with the Px48 chimney);
Job done;
All turning and drilling done at 2000rpm, apart from forming and filing, 685rpm, and parting off, 365rpm.
Click on the photos for a larger image.
Paul.
Monday, 2 June 2014
Roxey Mouldings ICI hopper part 5 - hopper 1.
Attention now turns to the hopper body. This is drawn as a single piece and should fold up as is. However, the floor has been drawn too wide, which means that there are gaps at the bottom of the body where the sides meet the ends. The solution, which is covered in the instructions, is to cut the body into 4 sections as below;
Easy work with a piercing saw with a fresh blade fitted. There are a series of half-etched rivet holes in the sides which need punching out, which are a bit vague in places so a bit of remedial work with a .4mm drill was required. Punching out was left until later.
Once cut into sections the floor can be narrowed. I scribed a line 1mm from the edge then set to work with tin snips;
My 'snips are Draper Expert Jewelry Snips which are well suited to this type of work.
The next job is to fold over the top lip to 90 degrees, I used a 5.5" Hold & Fold. As this is a very thin lip the fold lines were deepened with a square file until a slight witness line apeared on the opposite side to make folding easier. Then the body sides and ends can be folded, checking the ends against the sides until everything fits together with minimal gaps (some slight gaps are inevitable). Now the rivets can be punched out, to do so any earlier would risk flattening them in the Hold & Fold. Also rivetting tends to distort panels, folding strengthens the sides helping keep them flat.
Then with the body upside down on my surface table held together with Blu-Tack and tiny strips of masking tape it can be finally checked for squareness and tacked together.
More checking follows before final soldering. I work opposite corner to opposite corner to hopefully prevent any distortion and keep the heat down.
Here they are soldered together but not yet cleaned up properly, placed on the chassis;
All soldering done with my trusty 25W Antex and 188 degree solder.
Paul.
Easy work with a piercing saw with a fresh blade fitted. There are a series of half-etched rivet holes in the sides which need punching out, which are a bit vague in places so a bit of remedial work with a .4mm drill was required. Punching out was left until later.
Once cut into sections the floor can be narrowed. I scribed a line 1mm from the edge then set to work with tin snips;
My 'snips are Draper Expert Jewelry Snips which are well suited to this type of work.
The next job is to fold over the top lip to 90 degrees, I used a 5.5" Hold & Fold. As this is a very thin lip the fold lines were deepened with a square file until a slight witness line apeared on the opposite side to make folding easier. Then the body sides and ends can be folded, checking the ends against the sides until everything fits together with minimal gaps (some slight gaps are inevitable). Now the rivets can be punched out, to do so any earlier would risk flattening them in the Hold & Fold. Also rivetting tends to distort panels, folding strengthens the sides helping keep them flat.
Then with the body upside down on my surface table held together with Blu-Tack and tiny strips of masking tape it can be finally checked for squareness and tacked together.
More checking follows before final soldering. I work opposite corner to opposite corner to hopefully prevent any distortion and keep the heat down.
Here they are soldered together but not yet cleaned up properly, placed on the chassis;
All soldering done with my trusty 25W Antex and 188 degree solder.
Paul.
Subscribe to:
Posts (Atom)