Saturday, 18 March 2023

PST/Zebrano Gaz-03-30 Soviet City Bus - chassis and wheels.

 The chassis comprised of 12 parts, four of which made up the engine and exhaust. The chassis rails, rear springs and axle and the front axle/radiator fitted together reasonably well, however locating the engine to the gearbox to the chassis proved rather troublesome, the fit being vague at best, not helped by the V shaped arms that run from the clutch to the front axle. In fact I ended up having to lengthen the prop shaft to get it to fit, cutting it in half and inserting a short piece of .040" styrene rod;


Painting started with a wash with warm soapy water and a soft brush, followed by a coat of Hycote red oxide primer applied with my Badger 200NH. For the top coat I used my Badger 150 and Vallejo 862 Black Grey, a nice dull weathered black. At this stage whilst searching for images of the bus online I noticed that the chassis had two rods running from the rear axle to somewhere in front of the propshaft, quite where I couldn't quite make out as the kit differs from the prototype in the chassis layout. However, I decided to add an approximation of these from .020" styrene rod, scraping part of the paint away to get a bond;


Of course this meant getting the airbrush out again to blend in the new parts and touch up the paint where it had been scraped away, but that did give me an excuse to use my Aerograph;


To give me something to hold onto whilst painting the chassis I drilled a small (.8mm) hole in the top of the engine and inserted a cocktail stick to act as a handle.
The wheels were cleaned up, sprayed with Hycote grey primer (through the 200NH again), then sprayed with a mix of Vallejo 866 Green Grey and black. Once dry the hubs had a coat of plain black on the outer side, and black grey on the inner. This was done to give the impression of a bus that is cared for.
Here's the chassis right side up;


I also painted the radiator surround and the front bumper plain black, which contrasts nicely with the dirty chassis. The exhaust had a coat of Humbrol Leather, with it has to be said poor results. Humbrol paint isn't what it used to be I'm afraid.

Body next.


Paul.

Tuesday, 14 March 2023

Fixing a problem with my airbrush compressor

My airbrush compressor, an unbranded (although the pressure gauge has Sparmax written on it) TC-501C bought in 2008, recently developed a fault. When switched on it kept running after the set pressure had been reached rather than stopping automatically as it should. I checked the joints for leaks with soapy water, but found none so I started a thread on the Britmodeller forum (plastic kit modellers are far more likely to use airbrushes than railway modellers) asking for help. Someone replied suggesting that the pressure switch might have failed and advised me to contact air-craft.net for further advice and spares. This I did, and the helpful Martin agreed that it would be said switch, which had either failed or been blocked by debris. So, I removed the outer casing from the compressor, firstly by unscrewing the feet then undoing four screws in the base and disconnecting the on/off switch. Then the pressure switch, which is protected by a rubber cover and some heatshrink, could be unscrewed with a big-ish adjustable spanner. It can be seen in the photo below, with the rubber cover pulled back;


Note the exposed wires, these are mains leads so the unit needs to be unplugged whilst doing this!
I also removed the L-connector, and both connector and switch were cleaned out with cotton buds and toothpicks.


This is the switch, note the black crud and dirty water inside;


I then reassembled the switch and connector, with the switch sitting at 180 degrees to its original position as I found I got a better air seal that way;


I refitted the on/off switch and tested the unit, and I'm pleased to say that the pressure switch is now working as it should. I have however ordered a replacement from air-craft as I'm sure that I'll need it one day.
And here's the reassembled compressor;


With thanks to little-cars on the Britmodeller forum, and Martin at air-craft.net (usual disclaimer applies).

Paul.
 

Saturday, 4 March 2023

PST/Zebrano Gaz-03-30 Soviet City Bus - opening the box

An odd choice of model perhaps, but odd subjects do have a habit of catching my eye. The Gaz-03-30 was based on the Gaz AA truck chassis, which owed its origins to the Ford AA. Production started in 1933 at the Gorky Automobile Plant with the last bus coming off the line in 1950. The body was made from a wooden frame with metal cladding, and due to the poor roads and basic truck suspension needed to be completely replaced every few years. No heating was provided, but it was I suppose better than walking. This model represents a post war bus, after 1945 certain economies were made due to material shortages, hence the simplified angular front fenders (early buses had curved wings). See here for more information, and remember that Google translate is your friend. Information on these is pretty scarce to be honest.

This 1:72 scale kit is a collaboration between PST and Zebrano, two companies based in Belarus. 


Opening the box, the runners and instructions are sealed in a plastic bag;


Four runners are included. The parts look pretty good at first glance, with minimal flash although the detail is a bit 'soft', not as sharp as you would find on, say, a modern Airfix kit.
Here's the chassis and seats;


And the body;


There's no moulded clear parts, just a printed sheet of clear material;


Decals are included, but where do they go? The instructions are very brief and contain no information on positioning them, or even on livery. The exploded diagram does a reasonable job as far as showing where all the parts go though;


This is going to be an interesting build...
(It does strike me that this kit would make a decent freelance railbus in either standard or narrow gauge.)

Miniart make a 1:35 scale kit for this bus, and there are 1:43 scale die-cast models available on eBay. The die-casts all come in plain liveries with no markings.

Paul.