Wednesday, 15 April 2020

009 Ruston Proctor part 6 - frame detailing.

I've added some basic detail to the frame sides. Nothing too special, just enough so that something is there sitting in roughly the right place. Rivet detail has been ignored, well, there are limits...


Most of the detail has been added from microstrip, apart from the axlebox covers, which were turned from scrap styrene sprue, and the coil springs that sit above the leaf springs which are cut from that strange red styrene rod Slaters sell, with the reverse side filed flat. Some will no doubt wonder why I didn't use a section from a small screw, that was the original idea but as the piece is less that 2mm long and in shadow it just didn't justify the effort.


There are 27 separate parts per side. Which is quite enough thank you. Some parts are layered, which usefully adds different levels of relief to the frames. I still need to turn up a brass warning gong for the right hand side.


Its not perfect, but its good enough for this loco. The next job will be to make up a simple cab interior.

Paul.

Monday, 13 April 2020

009 Society open and single plank wagons

These two kits are part of a series produced for and sold by the 009 Society. Both are freelance in design, one is of a typical open wagon and the other a single plank bolster wagon. I left off the bolster to make a simple flat.

The bodies were undercoated with Hycote red oxide car primer, then painted with Revel 37 Reddish Brown, which I think suits them well. Axleboxes and brakes are Phoenix Precision Dirty Black. I wanted a bare wood interior, so I started with Revel 378 Dark Grey. This was followed by drybrushing on Humrol 29 then Revel 75 Stone Grey. This I hope gives a reasonable representation of bare wood, painting has never been my strength. I tend to use the same combination of paints for wood on all my stock, hopefully this allows my wagons to blend together.


Couplings are Greenwich, and slots needed to be filed in the bufferbeams to accommodate them, easily done with a square needle file. A shelf of plasticard off-cuts sits behind each bufferbeam to provide a greater surface to glue the couplings to.


I modified the brake gear slightly, removing a shoe from each assembly. The open has brakes on both sides of the wagon, the single plank is braked on one side only.

A fine pair of wagons which are in my view nicely detailed and proportioned. The open is especially nice, the higher ends adding character. I think that they look quite splendid behind a Saltford Peckett.


There's also a steel open in the same series, which I will build at some stage, and I'd like to build another planked open but this time cut the high ends down to match the sides.

For some reason the deck of the flat wagon appears lighter in the photos than it actually is. The delights of photographing in the garden on a sunny day...

Paul.

Friday, 10 April 2020

Unimat 3 dividing head

I've managed to get hold of a dividing head for my Unimat 3. I already have one, designed for use with the DB/SL and seen here, which could be used with the U3, but this one has certain advantages for me.
Note that the body has a separate indexing plate, which is held in place by the chuck when fitted;


These plates come in 4 different hole spacings; 24, 30, 36 and 40. Mine is a 24 hole plate, perfectly adequate for my needs. The front of the plate is marked in degrees, and the holes are on the rear;


There's a pin which locates in the plate, on the top left of the first photo, which can be withdrawn with the knob on the back seen top left in the above photo.

Here it is bolted down to the saddle, ready for drilling radial holes in the end of a length of brass bar;


And set up for milling flats etc.;


Note the locking knob on the back;


One side of the unit is shaped to clamp directly onto the lathe bed;


Note that the milling post is now clamped to the saddle. This means that the cutter is moved over the job, rather than the job being moved past the cutter.

Set up like this the dividing head matches the machine's centreline, meaning that the tailstock can be used to support longer work;


To use the milling post with this set-up the milling post needs to be bolted to the saddle, but spaced further away towards the rear. Emco make a mounting bridge for such work, but the milling table can be used to support the milling column instead;


The above is an extreme example, but it should give the basic idea.

The spindle nose is threaded M14, meaning that any chuck, collet chuck, or faceplate designed for the Unimat 3 will fit, which means that I can use a collet chuck rather than a 3 jaw for holding work, which I would prefer. The SL version needs a chuck with a separate back plate, which is a pain as aftermarket chucks without a back plate cannot be used.

All of the above photos are of course posed, and the motor has been removed for clarity.

Paul.