Tuesday, 23 July 2024

Mining remains around Buxton - back to Orchard Common

 Last time I looked at Orchard Common I did note a couple of areas of lighter vegetation which could have been possible mine shafts, but I didn't see any concrete marker pillars and as they were next to an old quarry working I ignored them. However, on studying my OS map whilst writing my previous blog post I did spot a couple of round marks that looked like shafts next to the quarry. I recently passed that way again and decided to take a closer look.

A quick look around revealed two markers on the ground. This is the southerly one, hiding behind reeds;


There's a circle of raised ground next to the shaft, waste brought up from sinking the pit was often used to build a raised area partly for a horse gin and partly to try and protect the pit from flooding.
The second marker is close by;


This one is a little harder to spot.
A close-up of the marker;


And, looking back at the first shaft from a higher vantage point;


The raised ground can be seen in the middle of the frame.
These two can be found at SK 0240 6940, and sit between the 3rd and 4th pits in my previous post.
Interestingly I've only seen those marker pillars on Orchard Common so far, I've not seen any on Axe Edge.
More info on markers and remains here.

Whilst taking these photos a curlew flew around calling out, a sight and sound that I never tire of.

Paul.

Sunday, 21 July 2024

Aerograph Super 63 airbrush

 Ever since I bought my slot-head Aerograph I've been keeping half an eye out for another with a larger paint reservoir. Eventually I won a boxed Super 63 for £21 on eBay;



I'm unsure of the age, but condition is generally good although the chrome is faded.

There's a cam inside, controlled by a ring behind the lever, which allows you to set the lever position and therefore the spray pattern, something that I can't see me using;


My first job, after fitting a quick release coupling, was to remove the tip and needle for inpection, both had what looked like ink residue on them. Next I filled it with neat screenwash and tried it out. I used screenwash as that's what I use to clean my 'brushes after use. This allowed me to check the spray pattern, which looked ok (my Super 93 had a worn tip which showed up at this stage). My only concern was the air valve which seemed a bit stiff and lacked sensitivity.
Nozzle and needle are interchangeable with my Super 93. The innards however are very different;


As can be seen I stripped mine down for a clean and just to see how it goes together. I'm not going into any detail about this, simply because it's a pain to put back together again so I wouldn't recommend doing it! All I will say is make sure the lever is pulled back on re-assembly and dig out your self-closing tweezers.
Once it was back in one piece I mixed up some Vallejo black and had a play;



I think my mix was a bit too thick, and I need to have a play with air pressure. This 'brush has a very fine tip (nozzle), about .18mm I think, so it will I feel be less tolerant than my other 'brushes where paint and pressure are concerned.

So far I'm pleased with it. Stripping it down might have been a pain but to me it was worth the effort as I have adjusted the air valve which now has a nicer feel. If I ever need to strip it again I'll probably leave the cam assembly off.


Paul.

Friday, 19 July 2024

Another Narrow Planet/6point5 R.A.R. gunpowder van

There were two versions of this kit (it seems to be discontinued now), to both 9mm and a 6.5mm gauges. I've previously built the 009 version, and now it's the turn of the 6point5 variant.
Originally the body was built using a printed shell with etched nickel silver inserts, however this was I believe quite costly to produce so later kits had a cast resin body. Both versions use a printed chassis. This build uses the cast body.
The kit comprises of the cast body, printed chassis, 6,5mm gauge wheels and tiny neothingyum magnets for couplings. Here's the body and chassis cyano'd together;


Note the coupling pin, I'm using link and pin couplings again. I've also filled in the holes in the end of the frames provided for coupling magnets.
The 6.5mm gauge chassis is, as you'd expect, narrower than the 9mm gauge version;


As I'm using 6mm gauge I've turned my own wheels, to 5.6mm dia., seen below next to the supplied 4mm dia. wheels;


The supplied wheels are really too small for the prototype, but with them fitted the coupling height matches Busch Feldbahn stock. My 5.6mm wheels bring the coupling height up to my preferred 6mm, and are closer to the prototype's diameter.
Painting started with a coat of Hycote red oxide primer, decanted from the rattlecan and applied with my Badger 200NH. The main body colour is Vallejo 70.982 Cavalry Brown with Vallejo 70.862 Black Grey used for the roof and chassis, the body being sprayed and the chassis brushed. As usual the number was done with a mapping pen and white ink. Vallejo matt varnish finishes the job off.


Alongside my 009 version;



And all of my 006 stock so far;



Another enjoyable build, and I'll be looking out for another unbuilt kit.

Paul.